Hello all
I had an error when i was installing
Intel® PROSet/Wireless Software and Drivers for Windows 8*
the error code is 2623
please help me !!
thank you !
Problem with installation Intel® PROSet/Wireless
↧
↧
Upgraded IRST to 11.6.0.1030 and now Windows 7 Will not Start Up
I just upgraded my Intel Rapid Storage Technology Driver to 11.6.0.1030 Using the recommended intallation method for an existing system. I have an ASUS p8Z77-v Premium motherboard and a RAID 1 configuration. The system was working fine before, with RAID and IRST turned on in the BIOS.
Now my Windows 7 x64 system will not start up. It starts to boot, but the Windows Logo just appears and hangs. Any help is greatly appreciated.
↧
Persistently Capturing Packets with VLAN Tags with Intel Pro/1000 CT NIC Card In CentSO 6.3
Hi,
I am in need to capture packets that contain VLAN tags on my Intel Pro/1000 CT NIC Card.
When I try to capture packets using the command: tcpdump -ni eth2 vlan
I do NOT capture any packets.
I then issue the command: ifconfig eth2 mtu 1522
I then try to capture packets using the command: tcpdump -ni eth2 vlan
I CAN now capture packets
I then save my settings in my cfg file: /etc/sysconfig/network-scripts/ifcfg-eth2
# Please read /usr/share/doc/initscripts-*/sysconfig.txt
# for the documentation of these parameters.
DEVICE=eth2
BOOTPROTO=none
NETMASK=255.255.255.0
TYPE=Ethernet
IPADDR=10.2.1.1
HWADDR=00:1b:21:a0:17:27
MTU=1522
I then reboot the computer.
After the reboot I issue the command: tcpdump -ni eth2 vlan
Now NO packets are captured.
I check the interface settings using: ifconfig eth2
The MTU setting is still there:
ifconfig eth2
eth2 Link encap:Ethernet HWaddr 00:1B:21:A0:17:27
inet addr:10.2.1.1 Bcast:10.2.1.255 Mask:255.255.255.0
inet6 addr: fe80::21b:21ff:fea0:1727/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1522 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:120 (120.0 b) TX bytes:4181 (4.0 KiB)
Interrupt:17 Memory:f0680000-f06a0000
I then issue the command: ifconfig eth2 mtu 1524 and ifconfig eth2 mtu 1522
(Toggling the MTU setting)
I then try to capture packets using the command: tcpdump -ni eth2 vlan
I CAN now capture packets
Any idea how to make the ability to capture packets permanent between reboots?
Thanks in advance for any wisdom and guidance!!
-John
Various settings:
ifconfig eth2
eth2 Link encap:Ethernet HWaddr 00:1B:21:A0:17:27
inet addr:10.2.1.1 Bcast:10.2.1.255 Mask:255.255.255.0
inet6 addr: fe80::21b:21ff:fea0:1727/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1522 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:120 (120.0 b) TX bytes:4181 (4.0 KiB)
Interrupt:17 Memory:f0680000-f06a0000
ethtool -i eth2
driver: e1000e
version: 1.9.5-k
firmware-version: 1.8-0
bus-info: 0000:30:00.0
modinfo -d -p e1000e
EEE:Enable/disable on parts that support the feature
CrcStripping:Enable CRC Stripping, disable if your BMC needs the CRC
WriteProtectNVM:Write-protect NVM [WARNING: disabling this can lead to corrupted NVM]
KumeranLockLoss:Enable Kumeran lock loss workaround
SmartPowerDownEnable:Enable PHY smart power down
IntMode:Interrupt Mode
InterruptThrottleRate:Interrupt Throttling Rate
RxAbsIntDelay:Receive Absolute Interrupt Delay
RxIntDelay:Receive Interrupt Delay
TxAbsIntDelay:Transmit Absolute Interrupt Delay
TxIntDelay:Transmit Interrupt Delay
copybreak:Maximum size of packet that is copied to a new buffer on receive
lspci
20:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
30:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
ethtool eth2
Settings for eth2:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000001 (1)
Link detected: yes
↧
Intel HD 4000 freezes my computer
I have Windows 8 and Intel HD 4000 graphics. The driver version is 9.17.10.2867. When I try to play a game in full screen it freezes my whole computer. Does anyone else have this problem? And is there a way to fix it?
↧
drivers for graphics Intel GMA 3600/3650 for Windows 7 x64 - When ?
drivers for graphics Intel GMA 3600/3650 for Windows 7 x64 - When ?
I have eyes , tell expected data of release
↧
↧
HDMI Output failure on windows 8 with Intel(R) HD Graphics WDDM1.1
Just upgraded to windows 8 on my laptop and now my HDMI output is no longer working. I was using windows 8 preview and the HDMI output worked just fine. I have tried to update the driver with this download:
but when I do I receive an error message that reads:
"This computer does not meet the minimum requirements to install the software."
I have tried using the windows 7 64 bit driver located here:
but my HDMI output doesn't work with that drivertput
Any help would be greatly appreciated. I miss my 22" monitor.
↧
Intel AT Service
Today I wanted to disable my subscription to Intel AT Service and I suspended it on web site. After that I was prompted to click “Synchronize Settings with Server…” in desktop app, but it returned “Synchronization Failure” message and didn’t unrolled my notebook.
What I need to do to disable that service on website and notebook?
↧
SOX5810J.86A.5599.EB.EXE Bios Update flagged as malicious by Comodo
Hello all,
I am trying to update my bios on my DX58SO motherboard with the file SOX5810J.86A.5599.EB.EXE downloaded from the support forums on Intels own website.
However, my Comodo Defense+ software flags it as extremely malicious and urges me to block the application from runnig - see included image.
Does anyone have any advice to give on this? Should I run the program anyway?
Thank you in advance.
↧
Processor microcode license for Linux
Hello,
When downloading the Intel Microcode .dat file for Linux, we are presented with license terms that significantly differ from what is present in the .dat itself. What are the real license terms on this file ?
See these links for reference :
http://lists.busybox.net/pipermail/buildroot/2012-September/058844.html
http://lists.busybox.net/pipermail/buildroot/2012-October/060023.html
Thanks for your help.
↧
↧
DZ77GA-70K bricked after disabling legacy boot (OO57 BIOS)
I just bricked my DZ77GA-70K after the setting some option in my brand new 0057 BIOS...
s
I'm usually booting using UEFI to Windows 8 system with success, previously with the 0053 BIOS.
After upgrade to the 0057 BIOS I noticed the Legacy Boot checked along with the UEFI boot checked. I decided to disable legacy boot and remove the USB and optical boot to reduce my boot time. I didn't touch to the new secure boot feature.
On reboot, no video output and two beeps :'(
I tried all the recovery methods: Back2BIOS button, configuration mode jumper (2-3), recovery mode jumper (no jumper at all), and removing the battery to clear CMOS all the night without AC cable. All attempts were unsuccessful.
My attached devices :
USB stick FAT 32 formatted (my usual BIOS upgrade stick) with only the brand new 0058 .BIO file on it, on the first yellow USB port, no other USB device attached (no mouse, no keyboard)
One DDR3-RAM stick (i switch between 4 ones to be sure one is not causing problems)
My steps with BIOS recovery mode (jumper removed) :
1. power on
2. status 31 : my usb stick is flashing
3. one beep
4. status 92 : two beeps, twice
5. status EA -> 77 -> 40 -> 42 -> 44 -> 48 -> 4A -> 4B -> FE (???), seems the last status (I waited 5 minutes)
6. reset button
7. status 15 -> 14 : three beeps, looping
8. reset button
9. status 15 -> 14 : three beeps, looping
And of course absolutely no video output...
I tried Intel Support by chat and the guy suggested me returning the MB to the reseller under warranty.
You really think that could happen only with setting a bad option in the BIOS ?
But... aren't all these recovery methods supposed to repair that ?
What there purpose if they all failed at restoring this setting ?
I switched from ASUS motherboards to Intel because I wanted serious work on hardware and BIOS level, and I'm really disappointed...
If you can help me, guys, I'll be very glad.
Geoffrey
↧
help - raid suport
i have a problem with intel storage technology
i have a hdd - 500gb and a ssdd 30 gb, but i don't understand wath ig going on with the computer
that is the print screen of the problem:
Someone help me, i 'm a noob with that!
i can't remove/deletethis "RAID volume"
↧
Not able to download the latest driver for Intel(R) HM76 Express Chipset LPC Controller - 1E59
I am not able to get hold of the latest driver for Intel HM76 Express Chipset LPC Controller - IE59, for Windows 8 Pro
Please help,
↧
No puedo instalar discos duros Sata II y con data en el nuevo computador
Buenas noches,
Tengo un equipo con 3 discos duros en un computador con SO Windows 7, los 3 discos duros son Sata II, 2 Seagate y otro Western Digital.
Estoy tratando de instalar estos discos duros con full datos en otro computador con Tarjeta madre DZ68BC y SO Windows 7. Tengo conectados 2 discos duros Seagate SATA III en los sockets azul oscuro y los discos del otro computador los estoy tratando de colocar en los sockets negros. No hay manera que el computador reconozca los discos Sata II en los sockets negros, el SO
Alguien me puede ayudar en este problema?
Gracias
↧
↧
DN2800MT vaapi driver bug
the vaapi drvier under ubuntu is buggy, heavy screen macroblocking ...
I followed this article to install:
Enabling Hardware Accelerated Playback for Intel ® Atom™ Processor N2000/D2000 Series
Case Study Using MPlayer on Ubuntu 12
especially when displaying Cast...
will someone fixit soon?
↧
Intel Rapid Storage Tech IAStorUI error , How to solve?
Hello, Since yesterday I see a Different Icon top dow my Win7 X64. when I select this Icon I have an error popup
See attached screenshots.
How to solve?
Thanks in advance
↧
DZ77RE-75K Won't POST at all
Hi All,
I just received my DZ77RE-75K and am trying to get it working. I have the following configuration in it now:
- DZ77RE-75K
- I7-3770K
- Corsair Vengeance 16GB (2x8GB) DDR3 1600 MHz (PC3 12800) Desktop Memory (CMZ16GX3M2A1600C10)
- EarthWatts EA-500
I installed the the board per instructions, including connecting the the 2x4 and 2x12 power cables. When I boot, I get no POST codes on the port 80 nor do I get any beeps. The fan spins up, but I get no display. The only activity are the VCCP1 through VCCP3 LEDs are blinking at a regular interval, but I get nothing else. I have reseated them memory, swapped the memory, and tried w/o the memory in with the same result. I have also pulled everything except the memory, CPU and power off the board with the same result. I've also reseated the CPU.
Any suggestions?
Thanks,
Ben
↧
HD4000 extremely slow when rotated (XP)
HD4000 is very slow when rotated 90/270. OS is Windows XP. Using latest driver (5421, 7/27/2012).
Disabling acceleration (control panel -> display -> settings -> advanced -> troubleshoot) fixes the performance problem, but then DirectX apps don't run and the Intel control panel doesn't run.
Here's another funny thing. Performance greatly improves if a 2nd monitor is connected.
Again, this is only when rotated. When not rotated, performance is better (or at least not worse) with acceleration enabled, and adding 2nd monitor makes no difference.
↧
↧
DQ77KB iSCSI boot
As it is possible boot OS on DQ77KB from ISCSI target? I not found any settings in BIOS and BootUtil not support update of NIC ROM. There is a way to enable iSCSI boot support on this motherboard? Or may be Intel can plans to add support of iSCSI boot in BIOS?
↧
HD4000: mouse cursor jumping when mouse pointer is changing
I'm running Win 8 (64) on my new HP EliteBook 8470p.
After connecting my secondary monitor (old Acer, 1280x1024) I noticed that whenever the mouse cursor is changing, for example while moving the pointer over a form field or text in firefox or moving it over the "border" of an application window, it's "jumping" a bit. This is quite irritating and also slowing down my workflow.
I reinstalled Windows, updated the HD4000 driver to the latest version (before that I tried the one from the HP support site, their driver is a bit older), without being able to solve the issue. The only thing that seems to work is to only use one screen. Otherwise my system is working fine.
I've searched the forum and found this message, that seems to describe a similar dual problem:
http://communities.intel.com/message/85665#85665
Thank you very much for your help!
Kind regards from Vienna (Austria),
Patrick
↧
MFS5520VIR boot issues on SSD RAID 1
Environment:
MFSYS25V2
Firmware: 11.6
Compute Module: MFS5520VIR
Boot Drive: Storage pool consisting of 2 Intel 320 Series 80GB SSDs (part #SSDSA2CW08) . Two virtual drives configured as RAID 1 arrays
OS: VMWare ESX 5.1
There are two compute modules that each have their boot drives configured on this storage pool. There are other compute modules in this chassis that use non-SSDs for their storage pools & virtual drives.
The two compute modules using the SSD virtual drives consistently have issues booting. The watchdog timer always performs a hard reset at least once on these compute modules during reboots, often two and three times. The two events that appear in the event log are:
3522 - BIOS FRB2 Watchdog timer expired - The server was hard reset
3520 - Watchdog timer expired - The server was hard reset
The compute modules that boot to drives in the non-SSD storage pools never have this issue. Has anyone else experienced this?
↧
More Pages to Explore .....
